LEO Satellite Contacts via Easy Sat and Linear Transponder Satellites

June 20, 2017 by AB1OC

LEO Satellite Station 2.0 Antennas

We recently did a Tech Night at our club on Building and Operating an LEO Satellite Ground Station. As part of my portion of our Tech Night presentation, I recorded several LEO satellite contacts. I made videos showing the operation of the computer controlling our Satellite Station 2.0 during these contacts. These videos give an idea of what it’s like to operate through LEO satellites.

The video above records several contacts through SO-50 – an FM “Easy Sat.”

In the next video, several contacts were made through FO-29, a linear transponder satellite.

The distortion you hear in my voice results from my voice coming back delayed through the satellites.

We will have our Satellite Station 2.0 setup at Field Day this year. If you are local to Nashua, NH, you are welcome to visit us during Field Day and see our Satellite Station in operation.

You can read more about the station used to make these contacts here on our Blog.

Fred, AB1OC

Nashua Area Radio Society’s 2017 Field Day Station Test

June 15, 2017 by AB1OC

ARRL Field Day is the Nashua Area Radio Society’s largest and most popular annual activity. You can see more about our recent Field Day activities on our Field Day page and our Blog. We recently got together for a Field Day Station Test.

Dave Merchant K1DLM, our Field Day chairman, is bringing 21st-century radio and computer technology to our Field Day setup this year. There are several aspects to this new component of our Field Day plans, including –

Two Flex-6700 Software Define Radios running over a network for our new Digital and enhanced GOTA Stations
An on-site WiFi Network to enable using the N1MM+ Logger in network mode for sharing log information, station activity, real-time scores, and messages
A central Score Board and Field Day Information Computer in our public information tent

2017 Field Day Site – Upper Field Layout

We will again be holding our 2017 Field Day operation at the Hollis-Brookline High School in Hollis, NH. We plan to use the upper baseball field area as our main operating location. We have decided to add a third tower this year and locate it on a soccer practice field several hundred feet from our main operating area. Our antennas and equipment will lie within the required 1000′ circle, but the third tower would situate those operating at that location away from the rest of our group. Dave’s solution to this problem was to set up a network and operate two Software Defined Radios (SDRs) at the lower site remotely from our location on the upper field.

Dave has enlisted Piece Fortin, K1FOP, as our IT Chairman for Field Day this year. Pierce has been instrumental, along with Dave, in the planning and testing of this new technology. Pierce and Dave have a great deal of networking, IT experience, and knowledge, and we could not have put together what is described here without them.

Dave K1DLM, Piece, Hamilton K1HMS, Mike Ryan K1WVO, Anita AB1QB, and I have gotten together multiple times to set up and test this new technology. I wanted to share more about the equipment and the associated testing (staged in the kitchen at our QTH – thank you, Anita!).

We began the testing process by setting up our 20m CW station.

20m CW Station Test

This station uses an Elecraft K3S Transceiver, a K1EL WinKeyer, and the N1MM+ Logger on a Windows 10 Laptop PC. We used this station to get our basic N1MM+ setup, including our Field Day CW keying macros working.

40m SSB Station Test

Next came our 40m SSB station. This setup uses an Icom IC-7300 Transceiver, allowing us to set up and test N1MM+ on the fly audio macro recording and playback. All three SSB stations will have on-the-fly recording and playback capability, allowing each SSB operator to record and use a custom set of audio macros.

Digital Station Test

Next came our Digital Station. This station uses one of the two remote Flex-6700 SDRs.

Remote Flex-6700 SDRs and Antenna Switch

Dave, K1DLM put together a really nice package for the two Flex-6700 SDRs and associated equipment, which will be located on the lower field. He used a rack system to mount the two SDRs, power supplies, a three-band Tri-plexor, a set of bandpass filters for 80m, 40m, 20m, 15m, and 10m, and a 403A 8×2 networked antenna switch. This setup allows either of the two SDRs to share the tri-band yagi or the 40m and 80m Inverted-V antennas on the tower on the lower field and operate on any of the 5 available HF bands. Antenna and filter switching automatically track the frequencies of the two SDRs making the setup simple.

Digital Station Second Display - SmartSDR & More N1MM+

Digital Station Second Display – SmartSDR and N1MM+

The Digital Station’s remote SDR will be operated using a SmartSDR client running on the Digital Station laptop PC. This station will have a second monitor to better accommodate all of the windows associated with it.

Digital Station Main Display – N1MM+

The main display associated with the Digital Station will run decoders for all PSK and RTTY modes. The ability to decode multiple PSK signals simultaneously and multiple RTTY decodes are available. The Digital station also acts as the N1MM+ master station in our Field Day setup for all other stations that use N1MM+.

Satellite Station Test

Our Satellite Station 2.0 was also added to the test setup. It uses a MacBook Air laptop running MacDoppler to control the antenna rotators and the Icom IC-9100 Transceiver, part of our Satellite Station. A Windows 10 Surface Pro computer, which runs N1MM+ and provides logging and other network functionality for our Satellite Station, is included.

GOTA Station Test

We also tested our GOTA station, which uses the second Flex-6700 SDR and a FlexRadio Maestro to provide a more conventional “buttons and knobs” interface for our GOTA operators. This station will also have a laptop PC running N1MM+ for logging.

Scoreboard Computer

We also built and tested a Scoreboard PC. This computer will be in the Public Information tent at Field Day and connected to a large display. It will show our real-time score, QSOs being logged as they are made, and other useful information about our Field Day operations. This computer will also continuously play videos from our Video Collection and provide access to IP video cameras monitoring the tower and equipment on the lower field.

Pierce, K1FOP and Hamilton, K1HMS Testing CW Stations

Our networked N1MM+ testbed contained at least one station of each type (CW, SSB, Digital, Satellite, and GOTA) that will be part of our Field Day setup this year. The Station Masters for the additional CW and SSB stations came by to test their setups using the test bed.

Field Day Networking System

The networking system Dave and Pierce built is central to all the technology described here. All of the gear is mounted in a single rack which will be located on the upper field during Field Day. The setup includes a Firewall/DHCP server, a commercial-grade outdoor WiFi access point, a 4G LTE modem for Internet access, an Ethernet Switch, and a UPS power supply.

MoCA Data Link Cable

The upper and lower fields at our Field Day site are separated by several hundred feet. A thick line of trees between the two locations raised concerns about connecting the upper and lower sites using WiFi. Pierce came up with a great solution to this problem – we will be using MoCA Data Modems and RG6 Quad Shield 75 ohm Coax Cable to provide a 10 Mbps data link between the two sites. We tested the MoCA link using a much longer coax cable run than we needed at Field Day and confirmed the full 10 Mbps throughput.

N1MM+ Talk Window

Our networked N1MM+ setup will allow any station in our setup to send messages to everyone who is operating at Field Day. We can use this capability for important communications like “Lunch is ready!” or “I need help from Pierce (our IT chairman) on the 40m SSB station,” or “The 6m band is wide open!”.

Our GOTA and Digital stations will be together in the same tent and will provide our Field Day 2017 visitors to see and use 21st-century Amateur Radio technology to make contacts. We are expecting young people who participated in our High-Altitude Balloon project and from other local schools where we have done Amateur Radio activities to attend. In addition to being a learning opportunity for all of us in the Nashua Area Radio Society, we hope that the state-of-the-art technology that we are using will generate interest among our visitors. If you are local to the Nashua, NH, USA area, come pay us a visit during 2017 Field Day. We’d enjoy providing you and your family a tour and a chance to Get On The Air. Hope to see you at Field Day!

Fred, AB1OC

A Portable Satellite Station Part 4 – 2.0 Station First Contacts!

March 3, 2017 by AB1OC

Station Packed and Ready for Transport

With our new 2.0 Satellite station built, tested, and packed; we were ready to try it in a portable environment. Fortunately, the Nashua Area Radio Club had a Technician License class coming up and we thought that the new station test would be a great way for our students to learn about Amateur Radio Satellites.

Satellite Status from AMSAT Website

Final preparations included checking the operational status of potential satellites on the AMSAT website. The page shown above is like a spotting cluster for LEO Satellites – it shows satellite activity reported by HAM satellite operators. Using this information, we configured MacDoppler to track the active satellites.

Satellite Pass Predictions

Next, we used MacDoppler to generate pass predictions for the weekend of our Technical Class. We assembled this data for all of the potential satellites and color-coded the available passes to identify those which had the best chance of producing contacts.

With this done, we loaded our portable tower, antennas, and all of the rest of the gear into our pickup truck and transported it to the class site.

Satellite Antennas Setup Portable

The first step at the class site was to unload all of our gear and move the portable tower to a suitable location. We used a compass to orient the tower to true north and leveled it. We used the weight bags that we made up to anchor the tower securely and then installed the antennas, rotator loops, and control cables. The antenna system worked out very well in the portable environment and was easy to set up.

Satellite Antenna Details

Here’s a closer look at the LMR-400 UF coax cables which connect the antennas to the rest of the system. The loops just behind the antennas are necessary to keep the coax from affecting the pattern of the antennas. The coax cables shown were made long enough to allow the antennas to be rotated through their full travel in the azimuth and elevation directions without binding.

Satellite Station Portable – Radio and Supporting Equipment

The final step in the portable setup was to put the IC-9100 Transceiver and Supporting Equipment together in the building and check everything out. We heard an ON4 station through FO-29 near the end of a low-angle pass as soon as we got everything hooked up and working. A very good sign!

We took some time to fine-tune the calibration of our rotators and to check the operation of the computer controls – everything checked out fine. The video above shows MacDoppler controlling the Azimuth/Elevation rotator and the IC-9100 Transceiver during the testing.

First Contact using New 2.0 Station (AO-85)

First Contact using New 2.0 Station (via AO-85)

With all the setup done, it was time to try to make our first contact. Fortunately, we did not have long to wait. We caught a medium-angle pass of AO-85, a U/V Mode FM Easy Sat. With MacDoppler setup and tacking, we immediately heard contacts being made through AO-85. I gave a whistle and adjusted my uplink VFO until I heard my signal coming back through AO-85. I gave a quick CQ call and immediately got a response from Jonathan, NS4L in Virginia, USA! It took a few seconds to exchange call signs and grid squares, and our first contract with our new station was in the log.

Explaining Satellite System to License Class

Our Technician License Class students were very interested in the station. We spent some time explaining the setup and demonstrating how it worked. We made more contacts between our class sessions using AO-85 and FO-29 (a V/U Mode Linear Transponder Satellite). Our most interesting contact was with Burt, FG8OJ, in Guadeloupe through FO-29. Working DX using the new station the first time we used it was great.

We learned several things during our first use of the new station. First, while the 35 ft. maximum separation allowed between the antenna system and the rest of the station is adequate in many applications, the antenna system’s close proximity to the building we were in blocked passes to the west of us with this separation. We have subsequently made up an additional set of feed lines using a pair of 100 ft. long 7/8″ hardline coax cables to allow for a greater separation in portable deployments such as this one.

We were glad we had the Heil Pro 7 Headset with us, and we used it for most of our contacts. The separate speaker allowed our students to hear the contacts well, and the boom microphone on the Pro 7 Headset eliminated feedback due to our voice coming back through the satellites. We improvised a mono-to-stereo converter cable to connect the Heil Pro 7 Headset to one of the two speaker outputs on the IC-9100 Transceiver. This allowed the radio to drive the separate speaker and the headphones at the same time.

We were glad to have the low-noise preamps available. These were especially useful during low-angle satellite passes, and our sequencing setup worked well.

All in all, the first test of our new 2.0 Portable Satellite station was a success. Our license classes students enjoyed learning about Amateur Satellites and had fun, along with us making contacts through a few of them. Our next goal will be to get packet modes and APRS working with our setup. We plan to do another article in this series when this part of our project is completed. Other articles in this series include:

We plan to add larger antennas and switchable polarity to our portable satellite station soon. This will enable us to make contacts using Satellites and the ISS in more difficult conditions.

You may also be interested in the satellite station at our home QTH. You can read more about that here.

Fred, AB1OC

A Portable Satellite Station Part 3 – 2.0 Station Radio and Supporting Equipment

March 1, 2017 by AB1OC

Portable Satellite Station Transceiver and Related Equipment

With the Antenna System for our 2.0 Portable Satellite Station complete, we turned our attention to assembling the Transceiver and supporting equipment. The equipment used for this part of the project includes:

Icom IC-9100 Transceiver and SP-23 Speaker
Green Heron RT-21 Azimuth/Elevation Rotator Controller (see Part 2 of this series for details on this device)
M2 Antenna Systems S3 Sequencers for Preamp Control
WaveNode WN-2 Wattmeter
Powerwerx SS-30 DV 30A Power Supply and RigRunner 4007U distribution unit
Heil Pro 7 Headset with Boom Microphone (desk microphone shown in the picture was used for testing only)
Apple MacBook Air laptop running MacDoppler Satellite Tracking Software

The Icom IC-9100 provides 100W on 2M and 75W on 70 cm, which is more than enough power for our application. It also has some nice satellite features, such as support for synchronized VFO tracking between the radio’s 2M and 70 cm VFOs. This radio also uses a single USB connection to allow computer control of the radio and the creation of a sound card interface on the host computer. A Heil Pro 7 Headset will be used for operator audio to avoid feedback due to our audio coming back from the satellite. The Icom SP-23 speaker is included to allow observers to hear satellite contacts while they are in progress.

Radio Management via MacDoppler

The MacDoppler software provides automated control of the IC-9100, including mode selection and automatic correction of both VFOs for the Doppler shift. These features greatly simplify the operation of the radio, especially when satellites with SSB/CW transponders are used.

The video above shows MacDoppler’s management of the IC-9100 Transceiver during a pass of AO-73. The constant adjustments of the VFOs take care of Doppler shift correction and ensure that our signal stays at a fixed position in the transponder passband of linear transponder satellites.

Preamp Sequencers and Output Monitoring

M2 Antenna Systems S3 Sequencers are used to provide control of the Advanced Receiver Research low-noise preamps on our portable tower. One of the nice features of the Icom IC-9100 is that it can be configured to provide separate keying lines for the 2M and 70cm VFOs. This allows a preamp to remain enabled on the receive VFO while the other VFO is in transmit mode with its preamp shutdown by the sequencer. This arrangement is very useful during tuning when one needs to hear your signal coming back from a satellite. A custom-made cable assembly was made to interconnect the S3 Sequencers with the ACC socket on the IC-9100, the Weatherpack connector on the tower preamp control cable, and DC power.

We used the excellent WaveNode WN-2 Wattmeter again in our portable satellite setup. This modular output monitoring system has sensors for VHF/UHF use as well as voltage, signal quality, and other monitoring functions.

DC power for the setup is provided via a Powerwerx SS-30DV Power Supply and a RigRunner 40007U distribution unit. We use this power supply in all of our portable setups. It is lightweight, provides plenty of power for a 100W station and accessories, and is quiet from an RF perspective.

Equipment Packing and Protection

With the transceiver test of the station complete, we turned our attention to transporting the setup. Proper protection of the equipment during transport was provided via a large case from Pelican. We combined this with a roller bag and an inexpensive storage bin for documentation and accessories, which are not very fragile. We also included our RigExpert antenna analyzer in the setup to make testing the station during setup in a portable environment easier.

Station Packed and Ready for Transport

With all of the assembly and testing of our 2.0 Portable Satellite Station components complete, we packed up all the components. We used an inexpensive furniture dolly to allow us to roll the tower around to load and unload it.

We are ready to test our new station in a portable application. More on that in the final article in this series. Other articles in the series include:

You may also be interested in the satellite station at our home QTH. You can read more about that here.

Fred, AB1OC

A Portable Satellite Station Part 2 – 2.0 Station Goals and Antenna System

February 22, 2017 by AB1OC

M2 Antenna Systems LEO Pack on Display at Dayton 2016

We came upon the M2 Antenna Systems booth while walking around the exhibit halls at Dayton last year. M2 had one of their LEO Pack satellite antenna systems on display there. This got us thinking about building a new, more capable version of our portable satellite station. The LEO Pack is a relatively lightweight circularly polarized antenna system for working satellites using the 2 m and 70 cm bands. It turns out that AMSAT members can purchase the LEO Pack at a discount. Starting with the LEO Pack in mind, I began to lay out some goals for a new 2.0 Portable Satellite Station:

Be capable of working all active Amateur LEO Satellites, including those using linear transponders and digital modes
Be portable and manageable enough to be set up in an hour or less
Be simple enough to operate so that HAMs who are new to satellites can make all types of satellite contacts with a relatively short learning curve
Be manageable to transport and store
Utilize computer-controlled antenna tracking to aim the antennas
Utilize computer control to manage radio VFOs to compensate for Doppler shift
Be easy to transport and store

Computer Controlled Satellite Station via MacDoppler Software

We decided to take a computer-controlled approach for both antenna aiming and Transceiver VFO management to meet our goal of making the station simple to operate for new satellite operators. After some research on the available options, we choose MacDoppler from Dog Park Software Ltd. for this purpose. MacDoppler runs under Mac OS/X and works well on our MacBook Air laptop computer, which is very portable. This program also has broad support for many different rotator and transceiver platforms and is easy to understand and use. Finally, the program features high-quality graphics, making the station more interesting to folks with limited or no experience operating through Amateur Satellites.

With the satellite tracking software chosen, we made selections for the other major components in the 2.0 Portable Satellite Station as follows:

Glen Martin RT-424 4.5′ Roof Tower to mount all of the antenna system components for portable operation
M2 Antenna Systems LEO Pack Antennas and Hardware
Yaesu G-5500 AZ/EL Rotator
Green Heron RT-21 AZ/EL Rotator Controller
Advanced Receiver Research Low-Noise Preamplifiers for 2m and 70 cm
S3 Sequencers from M2 Antenna Systems for preamplifier control
LMR-400UF Coax for feed-lines
MacDoppler Satellite Tracking software from Dog Park Software
Icom IC-9100 Transceiver
WaveNode WN-2 Wattmeter

I will explain these choices in more detail as our article series proceeds.

Glen Martin 4.5′ Roof Tower

Our solution to making the antenna system portable is built around a Glen Martin 4.5′ Roof Tower. This short tower is a high-quality piece made of extruded aluminum parts. The tower is very sturdy when assembled and is light in weight. We added a pair of extended “feet” to the tower, which is fabricated from 36″ x 2″ x 1 /4″ strap steel. This gives the tower a firm base and allows us to use sandbags to weigh it down (more on this later).

Our chosen Yaesu G-500 AZ/EL Rotator is a relatively inexpensive Azimuth/Elevation rotator suitable for lightweight satellite antennas such as those in the LEO Pack. This rotator can be installed as a single unit on the top of a tower or separated using a mast. We choose the latter approach as it is mechanically more robust and helps to keep the center of gravity for our portable antenna system low for improved stability.

Yaesu G-5500 Elevation Rotator

Separating the Yaesu AZ/EL rotator requires a short mast and a thrust bearing. The mast was made from a 1-3/4″ O.D. piece of EMT tubing from our local hardware store. The thrust bearing is a Yaesu GS-065 unit. Both of these pieces fit nicely in the Glen Martin Tower. The thrust bearing provides support for the LEO Pack and G-500 elevation rotator and greatly reduces stress on the azimuth rotator. We also added a Yaesu GA-3000 Shock Absorber Mount to the azimuth rotator. This part provides shock isolation for and reduces strain on the azimuth rotator during the frequent starts and stops which occur during satellite tracking.

LMR-400 Feed-lines And Antenna Connection Jumpers

LMR-400UF Feed-lines and Antenna Connection Jumpers

We decided to use LMR-400 UltraFlex coax throughout our antenna system. LMR-400UF coax provides a good balance between size, flexibility, and loss for our application. To keep feed-line losses reasonable, we limit the coax’s total length from the transceiver output to the antenna feed point to 50′. This results in a loss of about 1.3 dB on the 70 cm band. Our planned IC-9100 Transceiver, which has a maximum output of 75W on 70 cm, will deliver a little more than 50W maximum at the feed point of the 70 cm yagi. This should be more than enough power to meet our station goals. Allowing a total of 15′ for antenna rotator loops and transceiver connections, we settled upon 35′ for the length of our coax feed lines between the tower and the station control point.

Portable Tower Cable Connections and Base Straps

We added custom fabricated plates to the tower to act as a bulkhead for the feed line and control cable connections and to mount our low-noise preamplifiers. The control connections for the rotators and preamps were made using 6-pin Weatherpack connectors and rotator control cable from DXEngineering. The control cables are also 35′ long to match the length of our coax feed lines. This length should allow the tower and the control point to be separated by a reasonable distance in portable setups.

Low-Noise Preamplifiers from Advanced Receiver Research

We added tower-mounted Low-Noise Preamplifiers from Advanced Receiver Research to improve our satellite antenna system’s receive sensitivity and noise figure. Two preamps are used – one for the 2 m and one for the 70 cm antennas. While these units can be RF-switched, we decided to include the preamp control lead in our control cable to allow for control of the preamp switching via sequencers. This was done to provide an extra measure of protection for the preamps.

Levels and Compass for Tower Setup

We added a compass and a pair of bubble levels to the tower assembly to make it easier to orient and level it during setup. The picture above also shows the Yaesu shock-absorbing mount for the azimuth rotator.

Weight Bags to Anchor Portable Tower

Finally, we added a set of weight bags to securely anchor the tower when it is set up in a portable environment. These bags are filled with crushed stone and fastened to the legs of the Glen Martin tower with velcro straps.

LEO Pack Antenna Parts

With the tower and rotator elements complete, we turned our attention to the assembly of the M2 LEO Pack. The LEO pack consists of two circularly polarized yagis for the 2m and 70 cm bands. The 2m Yagi is an M2 Systems 2MCP8A which has 8 elements (4 horizontal and 4 vertical) and provides 9.2 dBic of forward gain. The 70 cm Yagi is an M2 Systems 436CP16 with 16 elements (8 horizontal and 8 vertical) and provides 13.3 dBic of forward gain. The Yagi’s are meant to be rear-mounted on an 8.5′ aluminum cross boom included in the LEO Pack. The picture above shows the parts for the two antennas before assembly. It took us about a 1/2 day to assemble and test the antennas, and both produced the specified SWR performance when assembled and tested in clear surroundings.

Assembled LEO Pack on Portable Tower

The picture above shows the assembled LEO pack on the portable tower. We attached a short 28″ piece of mast material to the cross boom as a counterweight to provide better overall balance and minimize strain on the elevation rotator. The antennas and the two outer sections of the mast can be easily removed to transport the antenna system.

2m Circularly Polarized Yagi Feed Point

The LEO Pack yagis achieve circular polarization via a matching network that drives the vertical and horizontal sections of the antennas with a 90-degree phase shift. The phase shift (and a final 50-ohm match) is achieved using 1/4 wave delay lines made of coax cables. We configured our antennas for right-hand circular polarization. The choice between right and left-hand circular polarization is not critical in our LEO satellite application as most LEO satellites are not circularly polarized. The advantage of circular polarization in our application is the minimization of spin-fading effects.

Green Heron RT-21 AZ/EL Rotator Controller

The final step in the construction of our antenna system was to add the rotator controller and test the computer aiming system. We have had very good results using Green Heron Engineering rotator controllers in our home station, so we selected their RT-21 AZ/EL rotator controller for this application. The RT-21 AZ/EL rotator controller is two rotator controllers in a single box. The rotator control parameters, such as minimum and maximum rotator speed, ramp, offset, over travel, and others, can be independently set for each rotator.

Rotator Test Using MacDoppler

The RT-21 AZ/EL Rotator Controller connects to our computer via USB cables. We run Green Heron’s GH Tracker software on our MacBook Air laptop to manage the computer side of the rotator controller and to provide a UDP protocol interface to the MacDoppler tracking software. The picture above shows the test setup used to verify the computer-controlled antenna pointing system.

Mixed OS/X and Windows Software Environment

One challenge associated with selecting a Mac OS/X platform for computer control is what to do about the inevitable need to run Windows software as part of the system. In addition to the GH Tracker software, the WaveNode WN-2 Wattmeter and digital modem software for satellite/ISS APRS and other applications require a Windows run-time environment. To solve this problem, we use a virtual machine environment implemented using VMware Fusion and Windows 10 64-bit on our MacBook Air Laptop along with Mac OS/X. The Unity feature of VMware Fusion allows us to run Windows apps such as GH Tracker as native Mac OS/X apps. The picture above shows an example of this.

Rotator Controller and Software Configuration

With the antennas removed from the cross boom, we tested the operation of the computer-controlled tracking system. The Yaesu G-5500 AZ/EL Rotator has some limits as to its pointing accuracy and backlash performance. Experimentation with the combination of the RT-21 AZ/EL rotator controller, GH Tracker, and MacDoppler setups was required to achieve smooth overall operation. We finally settled on a strategy of “lead the duck” tracking. The idea here is to set up the rotators so that they over-travel by a degree or so when the computer adjusts them and couple this with a relatively wide 2-3 degree tracking resolution. This maximizes the overall accuracy of the pointing system and minimizes the tendency towards the constant start-stop operation of the rotators during satellite tracking. Our current configuration for all elements involved in the tracking system is shown above.

With the antenna system complete and tested, we can move on to the next step in our project – the construction of a computer-controlled transceiver system. We will cover this element in the next part of this series. Other articles in the series include:

You may also be interested in the current satellite ground station at our home QTH. You can read more about that here. Our first permanent satellite station at our home QTH used Eggbeater antennas. You can read more about that system here.

Fred, AB1OC

Why Ham Radio?

February 20, 2017 by AB1QB

Fred’s Truck with Antenna

Every so often, I drive Fred’s truck to work and people ask me what that big antenna on the back of the truck is for. I explain to them that it is for Ham Radio. But the reply is usually, why ham radio – isn’t that outdated technology? We have cell phones and IM, etc…what do we need Ham Radio for? So I thought I would put down my thoughts as a relatively new Ham about why I enjoy spending so much of my time with Ham Radio.

amateur_radio_could_save_lives_in_times__2205260000_9445423_ver1-0_640_480

Amateur Radio for Public Service

Public Service

The number one reason we still need Ham Radio along with all the other technology we now have is for public service. When there is a disaster and cell phones, television, etc are all not working, Ham Radio operators provide the critical communication.

Ham Radio operators help locally to keep hospitals and first responders in contact with each other to help those affected by the disaster.

Hams also use our ability to communicate around the world on HF bands to help family members around the world to get in touch with loved ones affected by a disaster.

Ham Radio operators have been on the scene helping in every disaster from the earthquakes in Nepal to the recent flooding in California.

Amateur Radio Cube Satellites

Technology and the Maker Movement

I only became a Ham 5 years ago but many of my fellow Ham Radio operators got their license when they were in their early teens and used what they learned to launch their careers. Many have had very successful careers in STEM fields, all launched by their interest in Ham Radio at a young age. As technology advances, so does the technology used in our hobby. We even have a nobel laureate, Joe Taylor K1JT who is a ham. Joe has developed weak signal digital communication modes that let us communicate by bouncing signals off the moon!

As technology has advanced, so has the use of it in Ham Radio. Most Ham Radio operators have one or more computers in their shack. Many also have a software designed radio (SDR), where much of the radio functionality is implemented using Software, we use sound cards to run digital modes, which are a lot like texting over the radio, and we use the internet extensively as part of operating. We can also make contacts through satellites orbiting the earth and even the International Space Station.

Most hams love do-it-yourself technical projects, including building a station, home brewing an antenna, building a radio or other station component. In my day job, I am a program manager for software development projects, but its been a while since I have built anything. As a Ham I taught myself how to code in Python and about the Raspberry Pi and I built the DX Alarm Clock.

QSL Card from VK6LC in Western Australia

International Camaraderie

One of the coolest things about being an amateur radio operator is that you can communicate with other hams all over the world. Ham Radio is an international community where we all have something in common to talk about – our stations and why we enjoy ham radio. The QSL card above is from a memorable QSO with Mal, VK6LC, from Western Australia, who was the last contact that I needed for a Worked All Zones award. I must have talked to him for 1/2 hour about his town in Australia and his pet kangaroos!

Amateur Radio Map of the World

Geography Lesson

I have learned much about geography from being on the air and trying to contact as many countries as I can. There are 339 DX Entities, which are countries or other geographical entities and I have learned where each one is in order to understand where propagation will allow me make a contact. I have learned a great deal about world geography. Through exchanging QSL cards often get to see photos from so many areas of the world.

DXCC Challenge Award Plaque

Achievement – DXing and Contesting

DXing and Contesting provide a sense of achievement and exciting opportunity for competition. Many Hams work toward operating awards. You can get an operating award for contacting all 50 states, contacting 100 or more countries, contacting Islands, cities in Japan, countries in Asia, or anything else you can imagine. Each of these operating awards provides a sense of accomplishment and helps to build skills. Contesting builds skills through competition among Hams to see who can make the most contacts with the most places in 24 or 48 hours. Contesting also improves our operating skills and teaches us to copy callsigns and additional data accurately.

Teaching a License Class

Teaching Licensing Classes – Passing it On

Recently I have joined a team of club members who teach license classes to others who want to get licensed or upgrade their existing Amateur Radio licenses. Teaching provides a way to improve my presentation skills and also helps me to really understand the material that we teach about Amateur Radio. It is always a thrill at the end of the class to see so many people earn their licenses or upgrades.

There are so many interesting aspects of Ham Radio which is what makes is such a great hobby. Getting your license can open up a world of possibilities. Upgrading to a new license class provides more opportunities to communicate over longer distances. Ham Radio clubs, including our local club, the Nashua Area Radio Club, provide many resources to help you get your first license, upgrade to a new license class and learn about the many aspects of our hobby.

Anita, AB1QB

A Portable Satellite Station Part 1 – A Simple Station for AO-85

February 20, 2017 by AB1OC

Portable Satellite Station Contact

Our club, the Nashua Area Radio Club, has quite a few members who are interested in space communications. We built a simple portable satellite station last year for our 2016 Field Day operation to learn about satellite communications and create something new for folks to work with during 2016 Field Day.

Simple Portable Satellite Station

Our 1.0 Portable Satellite Station was a relatively simple setup built around an HT, an Elk 2m/70cm satellite antenna, and some gear to improve the receive performance and transmit power output of the HT. All of the gear was mounted on a board to make it easy to transport and it is powered by a LIPO rechargeable battery. The gear in our 1.0 station is made up of the following:

A Kenwood TH-72A Full Duplex 2m/70cm HT
A Heil headset with a boom microphone to make using the HT easier
A pair of 2m and 70cm Low-Noise RF switched preamps from Advanced Receiver Research
A Mirage BD-35 2m/70cm amplifier (this amp produces about 25 – 35W out when driven by the HT)
A Diamond SX-400 Watt Meter and an MFJ Dummy Load for testing and monitoring
A RigRunner DC distribution block with voltage and current monitoring and a 4S4P A123 LIPO Battery Pack
An Elk 2M/440L5 Dual-Band Log-periodic Antenna

Improved Satellite Antenna Support

Our first contacts with our 1.0 station were made using the Elk Antenna hand-held. Later, we created a “plumber’s special” setup with a camera tripod to make pointing the antenna easier. Note the angle meter from a local hardware store which measures the elevation angle of the antenna.

AO-85 (Fox-1A) U/V Mode FM Cube Satellite

This setup worked great for making FM contacts through AO-85 (Fox-1A), a U/V mode FM EasySat. We used the 1.0 station on multiple occasions including Field Day 2016 and several of our club members used it to make their first satellite contacts. The Full-Duplex HT allowed us to hear our own signal coming back from the satellite which was an important tool to help with aiming the antenna properly. The ELK Dual-Band antenna is also a good choice because it uses a single feed point and a single polarization for both the 2m and 70cm bands.

1.0 Station Team Operating Approach

We used the team operating approach outlined above. This worked especially well for new folks who had not made a satellite contact before as it enabled each of the three team members involved in making the contact to focus on a specific part of the contact. We used orange plastic tent stakes to make AOS, Time of Closest Approach, and EOS to mark headings for each satellite pass. Small flashlights used at the stakes made them glow for night-time passes.

We certainly had a lot of fun with our 1.0 Satellite Station and I expect that we’ll continue to use it. As we gained a little experience with AO-85, we decided that we wanted to build a more capable Portable Satellite Station that we could use to operate with linear transponder satellites and which included a tracking system and better antennas. I know from experience with our home satellite station that DX contacts are possible using higher altitude linear transponder satellites like FO-29.

We would also like to be able to use APRS and other digital modes through satellites as well as receive SSTV pictures from space.

These goals have become the basis for building our Portable Satellite Station 2.0. More on the new station in Part 2 of this series. Other articles in the series include:

You may also be interested in the satellite station at our home QTH. You can read more about that here.

73,

Fred, AB1OC

2016 ARRL Field Day!

July 8, 2016 by AB1OC

2016 Field Day Site Layout

I had the privilege of acting as the Field Day Incident Commander for the Nashua Area Radio Club this year. Field Day is the most important operating event for the Nashua Area Radio Club each year. We operated under our club callsign, N1FD and we were 7A here in New Hampshire, USA. We included some new antennas including a Three Element 40m V-Beam, a Satellite Station, and a 70cm Digital ATV Station in our operation this year. You can see some of the details which went into the planning of our 2016 Operation on our Club’s Tech Night Page.

The video above shows highlights from our 2016 Operation. As you can see, we had a lot of fun this year. Our club has 120+ members and we had a large turnout for Field Day. You can see more about our 2016 Field Day operation on our Field Day Page including photos, a score summary, and a recap presentation shared at a recent club meeting. I hope that you enjoy sharing our memories.

73,

– Fred, AB1OC

Dayton Hamvention 2016

June 1, 2016 by AB1QB

Anita Preseting in Contest Forum Fred, AB1OC, and I just returned from the 2016 Hamvention in Dayton, OH.

Our first day in Dayton was spent at Contest University – this was our 5th year in attendance but each year we learn more from the contesting experts. This year, we attended two presentations from Frank Donovan, W3LPL on operating techniques for the declining solar cycle and on 80m and 160m antennas. We also heard a talk from Val NV9L from Ham Nation on Log Analysis tools and another session on SO2R (Single Operator 2 Radio) Operating.

Slide from W3LPL Contest University Presentation

Friday was the first day of the Hamvention, and we spent most of the day visiting all of the vendor exhibits. We visited the Icom booth and looked at the new Icom 7851. It has an incredible display as well as one of the best receivers on the market.

Icom IC-7851 Display on a Large Screen TV

We also saw the new KX2 Transceiver at the Elecraft booth. It is even smaller than the KX3 and is perfect for SOTA and other portable operations. I would expect to hear some NPOTA activations using this radio.

Elecraft Kx2 on the Right, next to a KX3

Friday evening was the Top Band dinner, where we learned all about “Top Band Disease” from Larry “Tree” Tyree N6TR. Hams with this disease are nocturnal, and love the bottom of the sunspot cycle. They are constantly improving their 160m antennas – when you upgrade your receive antenna, there are people who can’t hear you, so you need to improve your transmit antenna – and the cycle continues…

2014 Amateur Radio Highlights

January 29, 2015 by AB1OC

Amateur Radio Highlights – our 2014 Readers Around The World

It is again time for our annual 2014 Year Amateur Radio highlights post. First, I’d like to thank our readers for their continued interest in our Blog. Our blog was viewed about 100,00 times in 2014 from 165 countries worldwide. You, our readers, have made 2014 our busiest year yet, and this provides Anita (AB1QB) and me with great encouragement to continue to provide content for our readers.

2014 was a very busy year in Amateur Radio for us. Our activities included a continued focus on station building, contesting, WRTC 2014, special events, providing presentations to help others in the hobby learn about new things, attending several HAM Events, progress on operating awards, and most importantly – time spent on the air operating.

microHAM Station Master Deluxe Antenna Controller

This year, we upgraded our fixed station to include a microHAM Station Automation system. This major project added some nice SO2R capabilities to our Multi-one station and automated the sharing of our antennas between our two SO2R operating positions. More of this project can be found here:

Eggbeater Antennas And Preamps SystemsOn Tower

Eggbeater LEO Satellite Antennas And Preamps Systems On Tower

We also added LEO Satellite capabilities to our station with the addition of some new antennas and electronics on our tower. This allowed us to make our first contacts through LEO birds with linear transponders. Our articles on this project include:

Our Mobile HF Station – Screwdriver Antenna

Our final major station-building project was constructing a state-of-the-art mobile HF station in our Ford F-150 pickup truck. We did this project in phases, starting with a simple setup using a 100W radio and HAM Stick antennas through the installation of a Screwdriver Antenna System for the 160m – 10m HF bands and concluding with the installation of an amplifier to enable high-power mobile HF operation. You can view the articles on this project here:

AB1OC Operating In the 2014 CQ WPX SSB

Anita (AB1QB) and I continued to be active in several contests this year. We both continued to develop our skills as contesters and our scores and place in the rankings reflected this. You can read more about our contesting activities and what we learned in the following articles:

WRTC 2014 Hollis Site Competitors, Support Team And Referee

We were also fortunate to host one of the WRTC 2014 competition sites. Along with our friend Scott Anderson, NE1RD, Anita and I acted as site managers for the only WRTC 2014 Competition Site in New Hampshire. You can read more about our WRTC 2014 experiences here.

13 Colonies Special Event QSL Card For K2K New Hampshire

Special event operations were a particularly fun part of our on-air activities in 2014. We operated as K2K, New Hampshire, in the 13 Colonies Special Event, W1AW/1, as part of the ARRL Centennial QSO Party, and as N1FD Celebrating the 35th Anniversary of the Nashua Area Radio Club. It’s great fun to operate in these events and the experience running the pileups that result continued to help Anita and me to develop our operating and contesting skills.

Introduction To The DXLab Suite

We prioritize devoting a significant amount of our Amateur Radio time to helping others in the hobby learn new things. In addition to writing this Blog, Anita and I try to create and deliver several presentations each year on a variety of topics of interest to the Amateur Radio Community. This year’s presentation included an update of our presentation on Amateur Radio Station Design and Construction and an Introductory Presentation on the DXLab Software Suite. We are always interested in working with Amateur Radio Clubs to deliver the presentation in person, where practical, or over the web.

Anita (AB1QB) and I with Bob Heil (K9EID)

We had the fortune to meet some of the legends in Amateur Radio this past year. Anita and I had the opportunity to get meet Bob Heil, K9EID and to appear on his Ham Nation podcast. Bob is an amazing gentlemen and we feel truly fortunate to have the opportunity to get to know him. We also had the opportunity to meet Fred Lloyd, AA7BQ, the President and Founder of QRZ.com. Fred visited our station and did an article about our station on QRZ.com. Anita and I both learned a great deal about HAM Radio and how it came to be what it is today as a result of the time these fine folks spent with us.

Joe Taylor’s WSJT Presentation At the ARRL Centennial Convention

Amateur Radio Conventions and HAM Fests were a major part of our Amateur Radio fun again this year. We were fortunate to attend and speak at the ARRL Centennial Convention in Hartford, CT USA this year – truly a once in a lifetime Amateur Radio experience. We also attended the Dayton Hamvention in 2014 where we had a chance to see all of the latest and greatest in Amateur Radio Equipment.

Our 2014 QSOs By Callsign

We were quite active on the air making almost 26,000 contacts between the two of us. As you can see from the graphic above, about 45% of our contacts were as part of Special Event Operations. We also made a little over 500 contacts from our mobile station, working over 100 DXCC entities in 2014 from the mobile.

Our 2014 QSOs By Band

We were active on all of the HF bands this year. We made our first contacts on the 60m band, and I was able to focus on the 6m band and earn a VUCC Operating Award (100 grid squares worked and confirmed) on that band. Anita and I made our first DX contacts in Europe on 6m in 2014. Anita took quite an interest in the 160m band, and she is working on a Worked All States Operating Award on this band. Our operating time using weak signal and satellite modes on the 2m and 70cm bands was limited to a few contacts this year. I did make my first contacts through LEO Satellites in 2014.

Our 2014 QSOs By Mode

We mostly operated in the SSB phone mode in 2014. Anita and I both continue to work on our CW skills, and we managed a little over 800 QSOs using CW in 2014. Anita was very active in the RTTY mode as part of her RTTY contesting efforts.

13 Colonies K2K New Hampshire QSL!

All of this operating resulted in quite a bit of QSL activity. We sent a total of almost 4,200 QSL cards in 2014!

We again made a video showing all of our contacts around the world in 2014. As you can see from the video, we were fortunate to work quite a bit of DX in 2014.

Fred’s 6M VUCC Operating Award

All of this operating helped Anita and me to make some progress on operating awards this year. In addition to earning a 6M VUCC, I completed a Worked All States Award on all 9 HF bands 160m-10m. I was also able to complete several nice regional operating awards (Worked All Europe TOP Plaque, Worked All VK Call Areas, and Worked All Africa) as well as upgrading my DXCC Challenge Award to the 1,500 Band Country level. Anita completed her JARL JCC Award (she worked 100+ Cities in Japan) as well as her Worked All States Triple Play Award (all states on SSB, CW, and Digital via LoTW).

Anita and I had a lot of fun with Amateur Radio in 2014. We look forward to another great year of HAM Radio fun in 2015. We hope to share some of what we learn and our experiences with our readers here on our Blog.

– Fred, AB1OC

Our HAM Station

Notes on the construction and operation of a multi-op Amateur Radio Station

Tag Archives: Satellites

LEO Satellite Contacts via Easy Sat and Linear Transponder Satellites

Nashua Area Radio Society’s 2017 Field Day Station Test

A Portable Satellite Station Part 4 – 2.0 Station First Contacts!

A Portable Satellite Station Part 3 – 2.0 Station Radio and Supporting Equipment

A Portable Satellite Station Part 2 – 2.0 Station Goals and Antenna System

Why Ham Radio?

Public Service

Technology and the Maker Movement

International Camaraderie

Geography Lesson

Achievement – DXing and Contesting

Teaching Licensing Classes – Passing it On

A Portable Satellite Station Part 1 – A Simple Station for AO-85

2016 ARRL Field Day!

Dayton Hamvention 2016

2014 Amateur Radio Highlights

Featured Articles